i ntegrated c ircuits d ivision www.ixysic.com ds-LCA220-r07 1 LCA220 common input, dual single-pole optomos ? relay e 3 pb part # description LCA220 8-pin dip (50/tube) LCA220s 8-pin surface mount (50/tube) LCA220str 8-pin surface mount (1,000/reel) parameter ratings units blocking voltage 250 v p load current 120 ma rms / ma dc on-resistance (max) 20 ? applications features description ordering information pin configuration ? telecommunications ? telecom switching ? tip/ring circuits ? modem switching (laptop, notebook, pocket size) ? hook switch ? dial pulsing ? ground start ? ringing injection ? instrumentation ? multiplexers ? data acquisition ? electronic switching ? i/o subsystems ? meters (watt-hour, water, gas) ? medical equipment?patient/equipment isolation ? security ? aerospace ? industrial controls ? 3750v rms input/output isolation ? low drive power requirements (ttl/cmos compatible) ? high reliability ? arc-free with no snubbing circuits ? fcc compatible ? vde compatible ? no emi/rfi generation ? small 8-pin package ? machine insertable, wave solderable ? surface mount tape & reel version available switching characteristics of normally open devices approvals ? ul recognized component: file e76270 ? csa certified component: certificate 1175739 ? en/iec 60950-1 certified component: tuv certificate: b 09 07 49410 004 form-a i f i load 10% 90% t on t off 1 2 3 4 8 7 6 5 + control - control load - switch #1 load - switch #1 load - switch #2 load - switch #2 nc nc LCA220 is a common-input, 250v, 120ma, 20 ? , dual normally open (2-form-a) solid state relay that has two independent, optically coupled mosfet switches controlled by a common input signal. it is provided in an 8-pin package, and employs optically coupled mosfet technology to provide 3750v rms of input to output isolation. its optically coupled outputs, which use the patented optomos architecture, are controlled by a highly efficient gaaias infrared led. common input optomos relays can replace standard dual-pole relays in a variety of applications. the common input relay eliminates the need to make an external circuit connection when both poles are controlled by the same signal.
i ntegrated c ircuits d ivision www.ixysic.com 2 r07 LCA220 absolute maximum ratings are stress ratings. stresses in excess of these ratings can cause permanent damage to the device. functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. absolute maximum ratings @ 25oc parameter ratings units blocking voltage 250 v p reverse input voltage 5 v input control current peak (10ms) 100 ma 1a input power dissipation 1 150 mw total power dissipation 2 800 mw isolation voltage, input to output 3750 v rms operational temperature -40 to +85 c storage temperature -40 to +125 c 1 derate linearly 1.33 mw / oc 2 derate linearly 6.67 mw / oc parameter conditions symbol min typ max units output characteristics load current continuous - i l - - 120 ma rms / ma dc peak t=10ms i lpk - - 340 ma p on-resistance 1 i l =120ma r on --20 ? off-state leakage current v l =250v p i leak --1 ma switching speeds turn-on i f = 10ma, v l = 10v t on --5 ms turn-off t off --5 ms output capacitance v l =50v, f=1mhz c out -50 - pf input characteristics 2 input control current to activate i l = 120ma i f - - 10 ma input control current to deactivate - i f 0.8 1.4 - ma input voltage drop i f = 10ma v f 0.9 1.2 1.4 v reverse input current v r = 5v i r - - 20 ma common characteristics capacitance, input to output - c i/o -3 - pf 1 measurement taken within 1 second of on-time. 2 input characteristics represent requirements of two parallel-connected leds. electrical characteristics @ 25oc
i ntegrated c ircuits d ivision LCA220 www.ixysic.com 3 r07 *the performance data shown in the graphs above is typical of device performance. for guaranteed parameters not indicated in t he written specifications, please contact our application department. performance data @25oc (unless otherwise noted)* typical led forward voltage drop (n=50, i f =10ma) 35 30 25 20 15 10 5 0 1.17 1.19 1.21 1.23 1.25 led forward voltage drop (v) device count (n) typical turn-on time (n=50, i f =10ma, i l =120ma dc ) 1.6 1.7 1.8 1.9 2.0 2.1 2.2 turn-on time (ms) device count (n) 25 20 15 10 5 0 typical turn-off time (n=50, i f =10ma, i l =120ma dc ) 0.30 0.50 0.70 0.20 0.40 0.60 0.80 turn-off time (ms) device count (n) 25 20 15 10 5 0 typical i f for switch operation (n=50, i l =120ma dc ) led current (ma) device count (n) 25 20 15 10 5 0 1.08 1.56 1.80 0.84 0.60 1.32 typical i f for switch dropout (n=50, i l =120ma dc ) 25 20 15 10 5 0 0.60 0.80 1.0 0.50 0.70 0.90 led current (ma) device count (n) typical on-resistance distribution (n=50, i f =10ma, i l =120ma dc ) 30 25 20 15 10 5 0 8.25 12.5 12.7 12.9 10.25 on-resistance ( : ) device count (n) typical blocking voltage distribution (n=50) 25 20 15 10 5 0 400 410 420 430 blocking voltage (v p ) device count (n) 390 440 typical led forward voltage drop vs. temperature temperature (oc) led forward voltage drop (v) 1.8 1.6 1.4 1.2 1.0 0.8 -40 -20 0 20 40 60 80 120 100 i f =50ma i f =30ma i f =20ma i f =10ma typical turn-on time vs. led forward current (i l =120ma dc ) led forward current (ma) turn-on time (ms) 5 10 15 20 25 30 35 40 45 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 50 55 typical turn-off time vs. led forward current (i l =120ma dc ) led forward current (ma) turn-off time (ms) 5 10 15 20 25 30 35 40 45 0.60 0.55 0.50 0.45 0.40 0.35 0.30 0.25 0.20 0 50
i ntegrated c ircuits d ivision www.ixysic.com 4 r07 LCA220 performance data @25oc (unless otherwise noted)* *the performance data shown in the graphs above is typical of device performance. for guaranteed parameters not indicated in t he written specifications, please contact our application department. typical turn-on time vs. temperature (i l =80ma dc ) temperature (oc) i f =10ma i f =20ma turn-on time (ms) -40 3.0 2.5 2.0 1.5 1.0 0.5 0 -20 0 20 40 60 80 100 typical turn-off time vs. temperature (i f =10ma, i l =80ma dc ) temperature (oc) turn-off time (ms) -40 0.6 0.5 0.4 0.3 0.2 0.1 0 -20 0 20 40 60 80 100 typical on-resistance vs. temperature (i l =120ma dc ) temperature (oc) on-resistance ( : ) -40 20 18 16 14 12 10 0 -20 0 20 40 60 80 100 i f =10ma i f =10ma i f =20ma instantaneous typical i f for switch operation vs. temperature (i l =120ma dc ) temperature (oc) led current (ma) -40 3.6 3.2 2.8 2.4 2.0 1.6 1.2 0.8 0.4 -20 0 20 40 60 80 100 typical i f for switch dropout vs. temperature (i l =120ma dc ) temperature (oc) led current (ma) -40 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -20 0 20 40 60 80 100 typical load current vs. load voltage (i f =10ma) load voltage (v) load current (ma) 200 150 100 50 0 -50 -100 -150 -200 -2.0 -1.5 -1.25 -0.625 0 0.625 1.25 1.875 3.0 maximum load current vs. temperature temperature (oc) load current (ma) 200 175 150 125 100 75 0 -40 -20 0 20 40 60 80 120 100 i f =20ma i f =10ma typical blocking voltage vs. temperature temperature (oc) blocking voltage (v p ) -40 340 335 330 325 320 315 310 305 -20 0 20 40 60 80 100 typical leakage vs. temperature measured across pins 5&6 or 7&8 temperature (oc) leakage ( p a) -40 0.10 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 -20 0 20 40 60 80 100 energy rating curve time load current (a) 1.2 1.0 0.8 0.6 0.4 0.2 0 10 p s 1ms 100ms 10s 100 p s 10ms 1s 100s
i ntegrated c ircuits d ivision LCA220 www.ixysic.com 5 r07 manufacturing information moisture sensitivity all plastic encapsulated semiconductor packages are susceptible to moisture ingression. ixys integrated circuits division classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, ipc/jedec j-std-020 , in force at the time of product evaluation. we test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. this product carries a moisture sensitivity level (msl) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard ipc/jedec j-std-033 . device moisture sensitivity level (msl) rating LCA220 / LCA220s msl 1 esd sensitivity this product is esd sensitive , and should be handled according to the industry standard jesd-625 . reflow profile this product has a maximum body temperature and time rating as shown below. all other guidelines of j-std-020 must be observed. device maximum temperature x time LCA220 / LCA220s 250oc for 30 seconds board wash ixys integrated circuits division recommends the use of no-clean flux formulations. however, board washing to remove flux residue is acceptable. since ixys integrated circuits division employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. chlorine- or fluorine-based solvents or fluxes should not be used. cleaning methods that employ ultrasonic energy should not be used. e 3 pb
i ntegrated c ircuits d ivision www.ixysic.com 6 r07 LCA220 mechanical dimensions dimensions mm (inches) pcb hole pattern 2.540 0.127 (0.100 0.005) 6.350 0.127 (0.250 0.005) 9.144 0.508 (0.360 0.020) 0.457 0.076 (0.018 0.003) 9.652 0.381 (0.380 0.015) 7.239 typ. (0.285) 7.620 0.254 (0.300 0.010) 4.064 typ (0.160) 0.813 0.102 (0.032 0.004) 8-0.800 dia. (8-0.031 dia.) 2.540 0.127 (0.100 0.005) 7.620 0.127 (0.300 0.005) 7.620 0.127 (0.300 0.005) 6.350 0.127 (0.250 0.005) 3.302 0.051 (0.130 0.002) pin 1 0.254 0.0127 (0.010 0.0005) dimensions mm (inches) pcb land pattern 2.540 0.127 (0.100 0.005) 9.652 0.381 (0.380 0.015) 6.350 0.127 (0.250 0.005) 9.525 0.254 (0.375 0.010) 0.457 0.076 (0.018 0.003) 0.813 0.102 (0.032 0.004) 4.445 0.127 (0.175 0.005) 7.620 0.254 (0.300 0.010) 0.635 0.127 (0.025 0.005) 0.254 0.0127 (0.010 0.0005) 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 0.65 (0.0255) 3.302 0.051 (0.130 0.002) pin 1 LCA220 LCA220s
i ntegrated c ircuits d ivision specification: ds-LCA220-r07 ? copyright 2012, ixys integrated circuits division optomos ? is a registered trademark of ixys integrated circuits division all rights reserved. printed in usa. 12/22/2012 for additional information please visit our website at: www.ixysic.com 7 LCA220 ixys integrated circuits division makes no representations or warranties with respect to the accuracy or completeness of the co ntents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. neither circuit patent licenses nor indemnity a re expressed or implied. except as set forth in ixys integrated circuits division?s standard terms and conditions of sale, ixys integrated circuits division assumes no liability whatsoever, a nd disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infri ngement of any intellectual property right. the products described in this document are not designed, intended, authorized or warranted for use as components in systems in tended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of ixys integrated circuits division?s product may resul t in direct physical harm, injury, or death to a person or severe property or environmental damage. ixys integrated circuits division reserves the right to discontinue or make changes to its p roducts at any time without notice. dimensions mm (inches) user direction of feed notes: 1. dimensions carry tolerances of eia standard 481-2 2. tape complies with all notes for constant dimensions listed on page 5 of eia-481-2 embossment embossed carrier top cover tape thickness 0.102 max. (0.004 max.) 330.2 dia. (13.00 dia.) k 1 =4.20 (0.165) 0 k =4.90 (0.193) p=12.00 (0.472) w=16.00 (0.63) bo=10.30 (0.406) ao=10.30 (0.406) LCA220str tape & reel
|
